Maintained by Carbidea · Updated October 2026
This guide assists completions and valve engineers specifying tungsten carbide needles, seats, and cages for severe choke service.
In gas wells with differential pressure over 35 MPa, Stellite 6 trims suffer wire-drawing washouts within 120 hours. High-velocity gas carrying quartz (100 to 250 μm solids) expands past orifices above 45 m/s, cutting grooves across seating tapers. Generic carbide grades chosen solely on hardness frequently suffer tip chipping or cracked cage bridges from hydraulic shock.
Choke trim specification requires separating shallow impingement wear from high-angle impact fracture. K. Haugen et al. demonstrated in "Sand erosion of wear-resistant materials: Erosion in choke valves" (Wear, Vol. 186-187, 1995, pp. 179-188) that optimized tungsten carbide grades improve erosion resistance by a factor of 50 to 300 compared to standard steels under silica slurry impingement. Their data showed that erosive loss depends on impact angle: shallow trajectories (15° to 30°) remove material via micro-cutting, whereas steep angles (75° to 90°) induce subsurface cracking and spalling. Severe trim specs must balance hardness with transverse rupture strength.
Choke trim assemblies endure vibration and thrust per API Spec 6A / ISO 10423 for PR2 testing:
Carbide blanks require 6.0 MPa vacuum Sinter-HIP processing to eliminate voids per ASTM B276 rating A02 B00 C00.
| Well Duty Environment | Reference Grade | Binder Chemistry | Grain Size | Density (ASTM B311) | Hardness | Min. TRS |
|---|---|---|---|---|---|---|
| Dry Gas + Fine Silt (ΔP > 25 MPa) | Ref. ISO K10 / WC-6Co | 6.0% Co | 0.8–1.2 μm | 14.95 g/cm³ | 92.2 HRA | 2000 MPa |
| Slurry + Coarse Sand | Ref. ISO K20 / WC-9Co | 9.0% Co | 1.4–2.2 μm | 14.60 g/cm³ | 90.1 HRA | 2500 MPa |
| Sour Gas Well (H₂S > 0.05 bar) | Ref. WC-9Ni / YN9 | 9.0% Ni | 1.2–1.8 μm | 14.55 g/cm³ | 89.8 HRA | 2300 MPa |
| Acidic Flood + Chlorides | Ref. WC-10(Ni-Cr) | 10.0% Ni-Cr | 1.0–1.6 μm | 14.45 g/cm³ | 89.5 HRA | 2200 MPa |
As an OEM sourcing partner for severe-service flow parts, Carbidea connects valve manufacturers with manufacturing partner mills. Our manufacturing partner mills operate under certified ISO 9001, ISO 14001, and ISO 45001 quality, environmental, and occupational safety management systems. Submit prints and fluid specs for evaluation and quotes within 1–2 business days.
A: Hydrogen sulfide and low pH fluids leach cobalt binder through galvanic corrosion. Unsupported tungsten carbide grains then detach under flow shear. Sour service requires nickel-chromium binders compliant with NACE MR0175 / ISO 15156.
A: High-velocity gas with fine silt causes low-angle erosion, suited for fine-grain grades (WC-6Co, 92.2 HRA). Liquid slurries with coarse sand produce high-angle impingement, demanding tougher grades (WC-9Co or WC-9Ni, TRS > 2300 MPa).
A: Needle guide stems and cage bores require an ISO H7/g6 clearance fit. Seating tapers must maintain concentricity within φ0.005 mm TIR and Ra 0.1 μm surface finishes for tight shutoff under API Spec 6A PR2 testing.
Related guides: Erosion vs. Corrosion · Seal Ring Failure Analysis · Carbide Grade Selection Guide
Related product category: Valve Parts for Oil & Gas →
Send a drawing or photo, get a quote in 1–2 business days.
Custom small-batch manufacturing to your print — prototype to production.
Request a Quote