Pressed Carbide: Green Compact, Sintered Blank, or Finished Part?

Ask whether pressed carbide means a green compact, an as-sintered blank, or a finished part. The drawing and quote must state grade, density evidence, tolerances, and acceptance.

Target Audience and Why This Problem Exists

This guide is for buyers and engineers ordering a pressed carbide preform for a wear part, tool blank, or seal component. The word "pressed" can describe the compaction step, an as-sintered blank, or a finished part that was once pressed. Those states carry different geometry, strength, inspection, and handling requirements.

Three Supply States

Supply state What the buyer receives What to verify before release
Green compact Powder compacted to a fragile shape before sintering Grade mix, pressing direction, green dimensions, and handling limits
As-sintered blank A densified near-net shape after sintering Density, porosity evidence, distortion, sintered tolerances, and grinding stock
Finished component A ground or otherwise machined part made from the blank Drawing dimensions, datums, functional faces, finish, and inspection records

The quotation should name one of these states. A price for a green compact is not comparable with a price for a ground part.

Why Pressing Mode Matters

Pressing is a process input, not a shape label. Powder filling, pressing direction, tooling, ejection, and green density affect what can be made and how the compact behaves through sintering. A 2023 Non-ferrous Metals study examines optimization of pressing modes for a VK10-HOM cemented carbide mixture (DOI:10.17580/nfm.2023.02.10). The practical point for a buyer is to discuss pressing direction and critical sections with the supplier rather than assuming any geometry can be pressed identically.

A green compact is not a serviceable carbide part. It can be fragile and is normally released for a controlled sintering route, not for installation. A sintered blank can be handled and measured, but functional bores, sealing faces, seats, and locating diameters may still require grinding or lapping. A finished part is accepted against the complete drawing.

What the Drawing Must State

State the supply state, material grade, quantity, geometry, grinding stock, critical faces, datums, and inspection method. Carbidea's production grade class is YG6X-grade fine-grain WC-Co at approximately 6% Co, with reference density around 14.9-15.0 g/cm3. Where required, density can be checked by ASTM B311 and apparent porosity by ASTM B276.

As-sintered features may carry 0.1-0.25 mm allowance, subject to the drawing. Designated ground or seating features can be quoted within 0.005-0.01 mm reference tolerance where the drawing confirms the feature. Never apply a finished-part tolerance to an unground blank. ISO H7/s6 also belongs only where the drawing specifies it.

If the geometry has undercuts, cross-holes, sharp internal corners, or very thin sections, ask whether the feature can be formed in the press direction or requires green machining and later finishing. A supplier should not accept a pressed shape that cannot be ejected, supported, or inspected.

Quote and Inspection Notes

Send the drawing revision, supply state, grade requirement, annual or prototype quantity, required records, and the faces that must remain protected. For a green compact, state the receiving condition and sintering responsibility. For a sintered blank, identify the dimensions that will be checked before grinding. For a finished part, list the final datums, fits, surface conditions, and inspection records.

Carbidea acts as a sourcing partner for custom carbide preforms and components, works with ISO 9001:2015 partner mills, and returns drawing reviews and quotations within 1-2 business days.

Related Products & Topics

FAQ

Q: Is pressed carbide ready to install?

A: Not if "pressed" means a green compact or an unground sintered blank. Confirm the supply state and all finishing operations on the drawing.

Q: Does an as-sintered blank have the same tolerances as a finished carbide part?

A: No. As-sintered features and precision-ground features are different drawing states, and each must have its own acceptance requirement.

Q: Should I specify density and porosity for every pressed carbide order?

A: Specify them when the drawing or application requires material evidence. If required, identify the test method, sampling basis, and record package in the order.